Onyx's Sprag Clutch HubConventional thinking says that the quicker you want your hub's clutch mechanism to engage, the more drag you'll have to put up with when you're coasting. This is because engagement time is most often associated with the number of points on the drive ring and the number of pawls - the more biting edges on the pawls and the more points on the drive ring, the more drag there will be as they all rub against each other when you're coasting. Having a quick engagement time is nice because then there's very little 'dead spin' in your crank arms, and having no lag in pick-up means you're putting the power down sooner. There are already hubs on the market that offer next to no lag, of course, but they're also plagued by a fair bit of clutch drag, which means that the bike isn't rolling as freely as it could be. That might be small beans for a lot of riders who don't even care if their brakes are dragging, but having as little drag as possible is important to a lot of riders, and especially to cross-country and road racers.
Onyx's rear hubs employ a sprag clutch that runs essentially drag-free when not engaged, but it also manages to offer what feels like instant engagement when it's time to put the power down. That near drag-free performance has made them the choice of some pro racers who, while being sponsored by another hub company, are looking for every possible advantage. Sprag clutches are not new - automotive companies, including Ferrari, have been using them in transmissions - and Onyx has been manufacturing sprag-equipped hubs at their Minnesota factory for four years now, but the system certainly seems to make a ton of sense for use on a bicycle.
So, how does the Onyx hub run nearly drag free
and offer instant engagement? Think of its sprag clutch as a one-way bearing that employs a number of asymmetrically shaped sprags (
the small metal pieces that looks like roller bearings in the photo above) instead of bearings. The shape of the spring-loaded sprags means that they allow for the barrel that's attached solidly to the freehub body to rotate freely in one direction, but they then wedge tightly against the barrel when force is applied in the opposite direction. Onyx says that the system can withstand any sort of torque that a rider's legs could ever apply, and that the mechanism is actually greased for life right from the factory with ISOFLEX LDS 18 Special A grease. In other words, don't mess with it.
The Onyx hub has a lot going for it, but there's no denying that its weight might turn some riders off - it's going to be heavier with the extra steel inside of it that makes up the sprag bearings, and Onyx refuses to use aluminum freehub bodies due to gouging and reliability concerns. A 12 x 142mm Onyx hub with an XD driver and 6-bolt rotor mounting weighs in at 364 grams, while the Center Lock version comes in at 463 grams. Those numbers are a bit higher than other options out there, but Onyx says that the lack of drag is of far more importance than the 50 - 100 gram weight penalty.
Because Onyx manufactures their own hubs from raw stock to finished product, they're able to offer them in pretty much any configuration that you can think of, as well as loads of different colours and even custom graphics. Want your name on the hub shell? No problem. They offer hubs for road, mountain, and BMX use, as well as front hubs, and pricing for all
can be found on their website.
Be sure to check out all of our Sea Otter Classic images in this gallery.
I thought you were joking.
You were joking right?
601-A Pine Ave., Goleta, CA 93117 USA, (805) 964-4545
stealth uses a roller bearing clutch. Onyx use a sprag clutch. they're very different designs.
I could try but It would be long winded and inaccurate. These videos give better descriptions (after the filler BS)
Sprag clutch:
www.youtube.com/watch?v=Fsp3fm4KHs0
Roller bearing clutch:
www.youtube.com/watch?v=QjR7dimpSJA
Onyx racing hubs are a new brand, and your BMX buddies haven't been riding them, that's BS. They can't slip.
Look closely at the pictures, the "roller bearings" are the ratchets, they lay flat when the hub coasts, then they ratchet (engage) against the inside of the hub body in drive. The engagement is nearly instantaneous and the coasting is nearly frictionless.
The Stealth hubs use a similar system, though it's not quite as durable and its not frictionless. Stealth makes good hubs, they also started in BMX.
Onyx Racing are the strongest hubs made, I run a set on a fat tandem, no other use could equal tandem torque, and the hub is like new.
Just to bring the rest of you up to speed .
Their website is a joke - a few haphazard pics of BMX stuff but zero tech info or other mention of MTB models & specs.
www.observedtrials.net/vb/f3/my-diy-roller-clutch-hub-48824
This Onxy design is the best commercial one I've seen.
Sweet project btw
Again, not the same system.
As a rider who climbs lots of mountains and weighs north of 250lbs. I have tested freehubs to the limit. As a result I do not ride 3 pawl/ring gear freehubs. Only DT stars and Chris King. IMO Chris King is the best engineered and most reliable freehub on the market.
The company is an industrial supplier for heavy equipment applications of the sprag clutch, they got into the bike hubs because one if their employees wanted to build a bomber hub.
If you are the kind of person who jumps on new products, the just do it, otherwise you wait with the rest.
The immediate engagement is second only to a muni!
The resistance is only slightly higher than a front hub.
They make no sound other than the sound that spokes make as they whistle in the wind.
Figure on a 100~150gm weight penalty